RC Pinion Gear Pitch Guide: 32P, 48P, 64P & MOD Sizes
Before buying a replacement RC pinion gear, identify two essential measurements: the gear's pitch or module must match the spur gear, and the pinion bore must fit the motor shaft. Tooth count is important, but a pinion with the right number of teeth and the wrong pitch or bore is not a substitute for the original part.
This guide explains the common 32P, 48P, 64P, MOD 0.6 and MOD 1 labels so you can narrow down the right gear family. Use your vehicle's manual, parts diagram and the gear maker's fitment information as the final authority.
What do 32P, 48P and MOD 1 mean?
Pitch and metric module describe the size and spacing of gear teeth. The imperial diametral pitch scale (P or DP) uses a higher number for finer teeth, while metric module uses a higher number for larger teeth. For standard gears, the approximate conversion is module = 25.4 ÷ diametral pitch.
- 32 pitch (32P): approximately 0.794 module. Browse 32P pinion gears.
- 48 pitch (48P): approximately 0.529 module. Browse 48P pinion gears.
- 64 pitch (64P): approximately 0.397 module. Browse 64P pinion gears.
- MOD 0.6: 0.6 metric module, which is not the same as 48P. Browse MOD 0.6 pinion gears.
- MOD 1: 1.0 metric module with larger teeth than MOD 0.6. Browse MOD 1 pinion gears.
32P versus MOD 0.8: The two sizes are very close, and some vehicle manufacturers specify compatible gear combinations. However, they are not mathematically identical. Check the maker's gear chart before mixing labels or suppliers. Do not assume that MOD 1, MOD 0.6, 48P and 64P gears can be interchanged.
Four checks before choosing a pinion
- Confirm the spur pitch. Identify the exact vehicle model, version and spur gear part number. Read the pitch or module in its parts diagram. The pinion and spur must use the appropriate matching tooth profile.
- Check the motor shaft diameter. Match the pinion bore to the shaft. For example, 3.0 mm and 3.17 mm (approximately 1/8 inch) are different diameters. Vehicle scale alone does not tell you the correct bore.
- Choose tooth count after fitment. “T” usually means the number of gear teeth: 13T is thirteen teeth; 25T is twenty-five. This number does not establish pitch or shaft fit. Be aware that “25T” on a servo horn normally refers to the output spline count, not pinion gear teeth.
- Verify material, clearance and mesh. Use a gear suited to the mating spur and confirm the motor mount has adequate adjustment. Follow manufacturer instructions for set-screw engagement, mesh and inspection after installation.
Example: reading a MOD 0.6 pinion specification
Integy C29172 is a 13T MOD 0.6 pinion with a 3.17 mm bore. Those three specifications describe tooth count, pitch and shaft fit. They do not establish that this part fits every brushless motor or every vehicle using a 13T pinion.
What happens when you change pinion tooth count?
With the spur and internal drivetrain unchanged, a larger pinion generally means less gear reduction and may increase top speed, while also increasing motor load and heat. A smaller pinion generally increases reduction, improving mechanical advantage at the cost of speed. Actual results depend on motor, voltage, tires, vehicle weight and operating conditions.
For example, a 60-tooth spur with a 15-tooth pinion has a 60 ÷ 15 = 4:1 ratio at that gear pair. With a 20-tooth pinion, the same spur gives 60 ÷ 20 = 3:1. Neither example includes internal transmission or differential ratios, so neither is a vehicle-specific gearing recommendation.
Set gear mesh safely
Power the vehicle off, disconnect the drive battery and let hot parts cool before working on the drivetrain. Follow the manufacturer's procedure for alignment, gear backlash and fastener tightening. If the gears bind, make unusual noise or run excessively hot, stop and recheck the setup rather than continuing to drive.
Where to shop after confirming fitment
Start with the Integy pinion and spur gear collection, then narrow by the correct pitch above. For other servicing information, visit our RC maintenance guide and product instructions. Always verify the exact product, compatibility and current stock before purchasing.
